Frequency check

In all the years I have been a ham and home constructor one item of test equipment I have never possessed is a frequency counter. Whenever I have needed to test if something is oscillating I have just stuck a bit of wire in the antenna socket of a receiver and listened for it, and if I have needed to tune an oscillator on frequency I have just tuned it for zero beat using a receiver that has been adjusted as best I could using WWV or similar.

Recently I decided that it would be useful to actually have a frequency counter, preferably a really accurate one. I know that it is possible to buy secondhand lab grade frequency counters on eBay. The trouble is that when your shack / workshop is the size of a broom cupboard there is no room for boat anchors. I didn't even have space for one of the inexpensive desktop frequency counters that are available. I decided that I would have to make do with a hand-held device. Farnell had one, but the price of £140 was rather too steep given the amount of use it was likely to get. I was about to give up when I came across the Yaege FC-1 being sold for about £30 on eBay.

My initial thought was that this was such a cheap device that it could not be very accurate and was probably not worth getting. The specification gives the time base accuracy as < 5ppm, which is worse than most ham radio transceivers. However, a bit of searching produced a PDF copy of the manual, which revealed that the TCXO module is user adjustable. I figured that I could get better than the quoted accuracy by regularly calibrating it using my rubidium frequency standard.

I ordered one from one of the Hong Kong traders and it came in just over a week. The antenna socket is a male SMA, similar to that used on the Chinese VHF/UHF hand-held radios and the opposite type to that commonly used by Japanese manufacturers. A short UHF rubber duck antenna is supplied with the counter. I ordered a BNC adapter so I could use my BNC whip antennas and also attach BNC terminated test cables.

I connected it up to my 10MHz rubidium frequency standard and found that it was already within a couple of Hz of the correct reading. The picture was taken before I set the gate time to 1 second which is necessary to get a reading down to 1Hz.

The time base oscillator adjustment is behind the battery compartment so you need to run the device from the charger while adjusting the frequency. You can see the adjuster in the picture on the right. Rather like adjusting the master oscillator in the Elecraft K2 the adjustment is incredibly touchy. The tiniest amount of movement can change the reading by a couple of Hz at 10MHz.

It turns out that it is not worth being so picky. The reading does slowly drift by a few Hz over a period of several minutes so you are never going to get absolute accuracy with a device like this. Nevertheless it is better than advertised and pretty good for the money, in my opinion.

One feature of the Yaege FC-1 that you don't get with most frequency counters is a signal strength reading calibrated in dBm, as you can see in the top photo taken while I was transmitting a carrier on 145.500MHz. I wasn't able to check how accurate the actual reading is but as a relative indicator the dB measurements seem quite accurate so this could be quite a useful tool for making antenna comparisons. It turns the frequency counter into a digital field strength meter.

Although it isn't a lab grade high accuracy frequency counter I think the Yaege FC-1 is a useful addition to my electronic test equipment and is extremely good value for money.

Spot on

Having an interest in weak signal narrow band modes, not to mention APRS which requires you to park your receiver on a specific frequency, I have always wished that the frequency readout on my radios could be relied upon. The QRSS band, for example, is only 100Hz wide. If your dial reading is out by that much, you'll miss it completely.

Many people try to calibrate their transceivers using WWV but that is not often a very good signal over here, and what with all the other carriers around 10MHz - many of them locally generated - you can never be sure that you have tuned to the right signal. I have wanted an accurate frequency reference for some time so a couple of weeks ago, following a comment by QRSS enthusiast Steve G0XAR, I ordered an Efratom LPRO-101 rubidium frequency standard on eBay. It arrived in about a week.

The unit I bought cost about £50 and came with a plug for the 10-pin connector and a 24V switched-mode power supply. These second hand units are widely available. New, they cost over $1,000 even in quantity. They are used in cellular base stations and are manufactured to have a maintenance-free life of ten years. To ensure reliable service the cellphone network providers take the equipment out of service before the ten years is up after which it is presumably shipped to China for reclamation. The used units should have several years of life in them, especially in occasional amateur use.

Rubidium frequency standards work by locking a crystal oscillator to the very precise frequency at which the amount of light from a rubidium lamp dips due to a phenomenon known as the hyperfine transition. A synthesizer locked to a reference oscillator is swept through this frequency until the dip is detected. The LPRO-101 includes an oven for the reference crystal, circuits to detect the dip and lock the oscillator, an output that tells you when the unit is locked, and the frequency reference output at 10MHz. The connector also provides signals that can tell you the state of health of the rubidium lamp. Once that fails you may as well scrap the unit because it can only be replaced by the manufacturer at a cost far in excess of what you paid for it.

To use the LPRO-101 you could simply attach a 24V supply and connect a cable to the 10MHz output. However, it's useful to have a circuit that shows you when the unit is locked on frequency. I used one shown in an article by KA7OEI built up on a piece of Veroboard, which uses a dual-colour LED to light red when the reference oscillator is unlocked and green when it is locked. You can see the circuit board inside the partially assembled case.

The voltage regulator and crystal oven inside the LPRO-101 generate a lot of heat so the unit is intended to be mounted on a heat sink. I purchased a Hammond extruded aluminium case to use for the project, which should provide reasonable heat sinking for the module.

One thing I learned from researching on the internet is that the LPRO-101 will run cooler when operated from its minimum recommended supply of 19V. This just so happens to be the output voltage of the power supply for an old Toshiba laptop whose screen failed so I decided to use that instead of the 24V supply that was sent by the seller.

The other thing I learned is that the rubidium lamps wear out with time. When they are made, the manufacturer ensures that they contain sufficient rubidium to achieve the stated maintenance free life of ten years, so the expected life in continuous use would be ten years less the use it has already had.

If I ran the unit all the time my rig is on - for example as an external frequency reference for a transceiver - then it is going to fail sooner or later. If I only use it for frequency calibration purposes, switching it on only when needed, then it will probably outlast me. The TCXO in my K3 is pretty stable so I should be able to obtain adequate accuracy for my purposes by manually calibrating the master oscillator using the rubidium standard and repeating this as often as necessary. How often that turns out to be, we'll see.

Here is the finished unit. Annoyingly, I messed up the front panel of the rather expensive Hammond case. Originally I had intended to use an SMA socket for the output but I didn't get the holes for its two mounting screws in the right place and after filing to fit it looked unsightly. So I fitted a BNC socket instead which is what I should have done in the first place. Unfortunately you can see the two holes for the SMA mounting screws either side of the BNC socket. So my frequency standard doesn't look quite as professional as this one built by DL2MDQ. Oh well, it's only a piece of test equipment!

Antenna analyzer from China

An antenna analyzer is a very useful piece of equipment and I have never regretted buying my AA-200, though I probably wouldn't get one now with the current model priced at £410.00. Even the basic MFJ-259B which is not exactly renowned for its quality construction will set you back £260.00. So I was interested to discover that the Chinese have entered the market with the Feature Tech AW07A which can be bought on eBay for a much more reasonable £160.00.

The unit can measure RF impedance and SWR from 1.8 to 490MHz (making it more directly comparable to the MFJ-269B model) as well as measuring capacitance and inductance. It may be used as a non-precision signal source and frequency counter, and with the addition of an inductor may be used as a dip meter. It looks like a nice addition to any amateur's toolkit.

A new toy

There was a knock on the door this morning and the postman asked me to sign for a parcel from overseas. The customs declaration amusingly - if appropriately - described the item as "Toy". It was the UNI-T UT-81B Oscilloscope Digital Multimeter that I ordered last weekend from eBay seller hk360radio in Hong Kong.

My first thought on opening the box was: "Wow! All this for a hundred quid? Amazing!" Inside the zip-up fabric carry case was the scope/multimeter, test probes, a BNC oscilloscope probe adapter, an opto-isolated USB cable for connecting the instrument to a PC, a two-pin wall-wart power supply and a two-pin to UK three-pin mains adapter, manual and CD containing the PC software.

The instrument is both a multimeter and a storage oscilloscope. The multimeter is auto-ranging, so the control switch simply selects the function: voltage, current, resistance etc. It measures DC voltages to 1000V, AC to 750V, current to 10A, resistance to 10M, capacitance to 100u and frequency to 10MHz. There is also a continuity tester. It can read volts down to 100uV and current down to 0.1uA. The frequency counter accuracy isn't good enough to calibrate your radio, but it's still quite handy.

Many years ago, back before I had a ham radio license, I had an oscilloscope that I built from a design in Radio Constructor magazine. It only covered up to about 200kHz and wasn't calibrated. I had to sell it when I left my parents home and had nowhere to keep so much electronic stuff, and I haven't had one since. But there have often been occasions when I wished I had one, so that was one of the main reasons for buying the UT-81B.

The oscilloscope bandwidth of the UT-81B model is quoted as 8MHz, so I can't use it as a monitor scope for the whole of HF, but it covers up to 40m at least. I was very keen to try this. I connected my FT-817 up to my QRP power meter via a T-piece and connected a cable between that and the oscilloscope. When I spoke into the microphone I could see the modulation envelope on the display.

I was interested to see whether the horizontal scan rate was fast enough that I could see the actual RF waveform. I increased the timebase speed until I was able to see the display above of the carrier wave from the FT-817 in CW mode. The sample rate is given as 40MHz and you can just see that the waveform is a little jagged. You can see that the scope has also displayed the frequency to within 1kHz. There is a full range of trigger functions and also a manual hold you can press to capture the display, which I used to take the photo above.

There is a Windows software application that connects to the instrument via a USB port. It can log measurements over time and also capture scope displays and save them to a bitmap (BMP) file. I was able to capture the waveform shown in the photo. However it was not able to capture an RF modulation envelope when sampling the RF at a much slower time base setting. I just got a thin wiggly line that seemed to bear no relation to the envelope displayed on the scope itself. Not a major issue, though.

I am really delighted with my new "toy", which cost me £95.50 plus £13 for the shipping (and no tax.)